Performer 289 (non-EGR)

Ford 260-289-302 V8
PERFORMER 289 (idle-5500 rpm)
Designed for street 260-289-302 c.i.d. Ford V8s without EGR. #2121 is stock replacement/street legal part for 289 and 302 V8s with OEM 4V carb.; 1966-72 (1973 non-CA); except stock equipped EGR. Will not fit Boss 302 or 255 c.i.d. V8s. Aftermarket 4-bbl carbs are not compatible with Ford Auto Overdrive Transmission (AOD) unless used with Lokar bracket SRK-4000.

Performer 318/360 (non-EGR)

Chrysler 318/360 V8
PERFORMER 318/360 (idle-5500 rpm)
Designed for street 318-340-360 c.i.d. Chrysler V8s. #2176 is stock replacement/street legal part for above V8s with OEM 4-bbl. carb.; 1966-72 (1973 non-CA); except stock equipped EGR. #3776 is stock replacement/street legal part for same V8s with OEM 4-bbl. carb.; 1972-87. These manifolds are not for use on marine engines used in salt water. Will not fit 1992 and later Magnum engines.

Carburetor Recommendations: OEM 4-bbl
Edelbrock Thunder Series AVS or Performer Series carb, 600-650 cfm, use our #1481 or #1843 Throttle/Transmission Lever Kit

Installation Notes: Recommended intake gasket: Edelbrock #7276 or Chrysler #4494462AB for 318 and #4397642 for 340 and 360 (or equivalent). Manifold height: A-4.13", B-5.13" see A/B Measurements. Port exit dimensions: .97" x 1.95".

Performer 351-W (non-EGR)

Ford 351 Windsor V8
PERFORMER 351-W (idle-5500 rpm)
Designed for street 351 c.i.d. Ford Windsor V8s. #2181 is stock replacement/street legal part for 351-W V8s with OEM carburetor; 1969-72 (1973 non-CA); except stock equipped EGR. Will not fit Boss 351. Aftermarket 4-bbl carbs are not compatible with Ford Auto Overdrive Transmission (AOD) unless used with Lokar bracket SRK-4000, see note at the bottom of this page.

Carburetor Recommendations: Edelbrock Thunder Series AVS or Performer Series carb, 600-650 cfm, for auto. trans. use our #1483 & #1491 or #1844 & #1846

Installation Notes: Use 12-bolt intake gasket set (Edelbrock #7220 recommended). Van installations use OEM Ford "van" gasket set; will fit early 16-bolt head with Ford 16-bolt intake gasket set. Choke block-off cover plate #8981 included. Manifold height: A-3.40", B-4.75" see A/B Measurements. Port exit dimensions: 1.10" x 1.80".

Performer AMC (non-EGR)

AMC 290-401 V8
PERFORMER AMC (idle-5500 rpm)
Designed for 1970-91 street 290-304-343-360-390-401 c.i.d. V8 engines. Available with or without EGR. Will not accept stock Motorcraft spread-bore carburetor. #2131 is a stock replacement/street legal part on 360-401 V8s with OEM carb; 1970-72; except stock equipped EGR.

Carburetor Recommendations: OEM 4-bbl. non-EGR square-bore, carb requires #8008 or #8024 stud, nut & washer kit Edelbrock Thunder Series AVS or Performer Series carb, 500-650 cfm.

Installation Notes: Recommended intake gasket: Edelbrock #7213 or Fel-Pro #MS96011. #2131/#21311 must use factory metal valley tray gasket. Manifolds have two center bolt holes offset. Manifold height: A-4.20", B-5.50" see A/B Measurements. Port exit dimensions: 1.03" x 2.07". Bracket #8034 required for 1979 and later vehicles.

Performer Vortec (non-EGR)

Chevrolet 262-400 Small-Block V8
PERFORMER VORTEC (idle-5500 rpm))
Based on the popular and powerful Edelbrock #2101, this dual-plane intake is designed for the street rod, industrial and engine swap market utilizing 262-400 c.i.d. Chevy V8s with 1996 and later Vortec (L31) cast iron or the new Edelbrock E-Tec aluminum heads. Manifold has provisions for external water bypass and may be used on either Vortec blocks or 1995 and earlier blocks. No provision for exhaust heated chokes. Accepts both square-bore and spread-bore carbs and late model waterneck, alternator, HEI and air conditioning brackets. Will not fit under stock Corvette hood. Available with standard finish or EnduraShine finish for a look you've got to see to believe.

Carburetor Recommendations: OEM 4-bbl. (pre-1981, electric choke only) - Use our #8032 throttle bracket
Edelbrock Thunder Series AVS or Performer Series carb, 500-650 cfm, use bracket #8032 for 1972-78.

Installation Notes: Recommended intake gasket: Edelbrock #7235. Manifold height: A-3.87", B-5.28" see A/B Measurements. Port exit dimensions: 2.05" tall (odd shaped width). Stock brackets will require modification to fit the upright manifold bolt holes.

Performer 460 (non-EGR)

Ford 429/460 V8
PERFORMER 460 (idle-5500 rpm)
Designed for street 429/460 c.i.d. Ford V8s. #2166 is stock replacement/street legal part for 429 & 460 V8s with OEM 4-bbl. carburetor with electric choke; 1968-72 (1973 non-CA); except stock equipped EGR. #3766 is stock replacement/street legal part for 460 V8s with OEM 4V carburetor with electric choke; 1979-87. Will not fit 429 Cobra-Jets or 1966-68 462 Lincolns and will not accept stock spread-bore carb. Will not fit 1988 and later models. #3766 cannot use #8714 to block-off EGR. Must use stock EGR plate.

Carburetor Recommendations: #2166: Edelbrock Thunder Series AVS or Performer Series carb, 650-800 cfm, for auto. trans. use our #1483 & #1495 or #1844 & #1848
#3766: OEM square-bore carb

Installation Notes: Recommended intake gasket: Fel-Pro #MS96018. Replacement EGR plate gaskets: #3898. Manifold height: A-3.75", B-4.49" (same as stock); Carb pad height: 4.12" see A/B Measurements. Port exit dimensions: 1.65" x 1.96".

Performer (EGR),p>Chevrolet 262-400 Small-Block V8
PERFORMER - '86 & EARLIER (idle-5500 rpm)
Designed for street 1955-86 262-400 c.i.d. small-block Chevys. #2101 is stock replacement/street legal part for 302, 327 and 350 V8s with OEM 4-bbl. or Edelbrock #1400 carb; 1966-72 (1973 non-California) cars, 1966-83 trucks and Suburbans; except stock equipped EGR. #3701 is stock replacement/street legal part for 305, 350 and 400 V8s with OEM 4-bbl. or Edelbrock #1400 carb.; 1972-86 and GM corporate engines with 350 V8s; 1981-86. Performers accept late-model choke, waterneck, air-conditioning, alternator and H.E.I. Has provisions to add oil fill tube. Not for 1987 and later cast iron or Chevy Bowtie heads. Will fit 1987 and later stock aluminum heads. Available with standard finish or polished.

Carburetor Recommendations: OEM 4-bbl., use choke rod #9171, bracket #8031 or #8036 for 1972-78 Edelbrock Thunder Series AVS or Performer Series carb, 500-650 cfm, use bracket #8031 or #8036 for 1972-78.

Installation Notes: Use adapter #8035 for clamp-on EGR valve. With carb #1400 & #3701, EGR spacer #1476 is required. #1476 is required with #3701 on centerbolt heads with 1986 & earlier bolt pattern. Choke plate #8901 included. Recommended intake gasket: Edelbrock #7201. Manifold height: A-3.50", B- 4.60" see A/B Measurements. Port exit dimensions: 1.14" x 1.88".

Performer 351-2V (non-EGR)

Ford 351 Cleveland V8
PERFORMER 351-4V & 351-2V (idle-5500 rpm)
Performer 351-4V is designed for street 351-C and Boss 351 Fords that came stock with 4V carb and heads. Performer 351-2V is designed for street 351-C and accepts 4V carb, however it's designed to improve the performance of engines that came stock with 2V carb and heads. Neither manifold will fit Boss 302 or accept stock Motorcraft spread-bore carb. Valley width measures 6-31/32".

Carburetor Recommendations: Edelbrock Thunder Series AVS or Performer Series carb, 600-800 cfm (see Carbs & Accessories), for auto. trans. use our #1483 & #1493 or #1844 & #1847.

Installation Notes: Choke block-off plate included with Performer 351-2V #2750. Recommended intake gasket: Fel-Pro #1228 (for #2665) or #1240 (for #2750). Manifold height: A-3.50", B-4.30 see A/B Measurements. Port exit dimensions: #2665 - 1.37" x 2.15"; #2750 - 1.30" x 1.86".

Performer Vortec V6 (non-EGR)

Chevrolet 90° V6
PERFORMER VORTEC V6 (idle-5500 rpm)
Based on the powerful Edelbrock #2111, this dual-plane intake is designed for the engine swap market utilizing 1985 & later Chevy 200-229-262 c.i.d. (3.8L and 4.3L) V6 engines with Vortec heads. With this new manifold, rodders can take advantage of the higher flow available with the Vortec head design. Performer Vortec V6 #2114 has provisions for external water bypass and may be used on either Vortec blocks or 1995 and earlier blocks. Designed for use with Edelbrock Performer Series 500 cfm carbs, it accepts late model waterneck, alternator, HEI and air conditioning.

Carburetor Recommendations: Edelbrock Performer Series carb, 500 cfm.

Installation Notes: Recommended intake gasket: GM 12529196. Manifold height: A-3.50", B-4.18" see A/B Measurements. Port exit dimensions: port exit is 2.05" tall with slanted side walls.

Performer Olds 350 (non-EGR)

Oldsmobile 307-403 V8
PERFORMER OLDS 350 (idle-5500 rpm)
Designed for street 307-330-350-403 c.i.d. Oldsmobile V8s, 1966-85. For non-EGR, the #2711 manifold comes with a universal pad to fit most carburetors with electric chokes For EGR, #3711 is stock replacement/street legal part for 307, 350 and 403 V8s with OEM 4-bbl. carb.; 1972-85; except 1976 with back pressure EGRs. 350 GM Corporate engines, 1981-86, use Performer #3701 for stock replacement. Will fit 1980-1/2 to 1985 307 c.i.d. V8s with 5A heads (casting #3317).

Carburetor Recommendations: #2711: Edelbrock Thunder Series AVS or Performer Series carb, 500-650 cfm (see pages 29-40). #3711: OEM 4-bbl.

Installation Notes: Edelbrock Performer Series, Thunder Series AVS and Carter AFB carburetors will not fit #3711. Recommended intake gasket: Fel-Pro #MS96027. For 403 Pontiac Trans Am, use OEM 4-bbl. only (for shaker hood clearance). EGR block-off plate included. Use choke block-off plate #8951 (included). Factory cruise control will not clear EGR valve without linkage alteration. For EGR applications, use stock carb only. HEI will clear this manifold. Manifold height: A-2.50", B-3.90" see A/B Measurements. Port exit dimensions: 1.18" x 1.86".

Performer 351-4V (non-EGR)

Ford 351 Cleveland V8
PERFORMER 351-4V & 351-2V (idle-5500 rpm)
Performer 351-4V is designed for street 351-C and Boss 351 Fords that came stock with 4V carb and heads. Performer 351-2V is designed for street 351-C and accepts 4V carb, however it's designed to improve the performance of engines that came stock with 2V carb and heads. Neither manifold will fit Boss 302 or accept stock Motorcraft spread-bore carb. Valley width measures 6-31/32".

Carburetor Recommendations: Edelbrock Thunder Series AVS or Performer Series carb, 600-800 cfm, for auto. trans. use our #1483 & #1493 or #1844 & #1847.

Installation Notes: Choke block-off plate included with Performer 351-2V #2750. Recommended intake gasket: Fel-Pro #1228 (for #2665) or #1240 (for #2750). Manifold height: A-3.50", B-4.30 see A/B Measurements. Port exit dimensions: #2665 - 1.37" x 2.15"; #2750 - 1.30" x 1.86".

Performer Buick 455 (non-EGR)

Buick 400-455 V8
PERFORMER BUICK 455 (idle-5500 rpm)
Designed for street 400-430-455 c.i.d. Buick V8s. #2146 is stock replacement/street legal part for 400, 430 and 455 V8s; 1967-71; except stock equipped EGR. Manifold not equipped with EGR. Will fit cold air induction hoods. Will not fit Buick 350.

Carburetor Recommendations: OEM 4-bbl. Edelbrock Thunder Series AVS or Performer Series carb, 650-800 cfm.

Installation Notes: Recommended intake gaskets: for 1967-76, Edelbrock #7246 or Fel-Pro #MS96005; 1972-76, Fel-Pro #MS96014. #2146 accepts divorced choke-type Quadrajet only. Manifold height: A-3.80", B-4.75" see A/B Measurements. Port exit dimensions: 1.14" x 2.26".